This is a quick drill for you company officers and acting officers. So much of what we do is coach and mentor our younger firefighters. When we are out and about we need to take the time point out things that might be obvious to us, but maybe not so much to others on our crew. (more…)
Category: ‘rescue’
Simple Low Profiling Clip for SCBA
The attached vidoe is a very short and simple clip about how teach firefighters to low profile. As we tell firefighters in our classes, removing your SCBA should be a last resort, but a skill that you must be proficient at. Being prepared is as much about mastering the basics as it is about being able to perform in the event that conditions dictate survival skills must be used. (more…)
The Build Up: Progressive Drills
This past Fall we were doing a Survival class and one of the drills we do is the “following the coupling” drill. It is one of the most basic of drills and is well known throughout the fire service. We have posted on this drill before on using a cut piece of hose to hand to your firefighters and have them tell you which way would be back to the truck.
We get comment about how basic this drill this and some like to try and shrug it off. Well, as we all know, we must master the basics. Like in athletics, we building the fundamentals and gradually move to more advance skills that expand on those fundamental skills. On the surface these skills are very basic but look a little harder; we can make these advanced drills easily that will incorporate the basic skill and more advanced techniques.
This is true for any drills, start with the most basic and when mastery is achieved, add to the drill and make it more advanced. Do this in steps and before you know it you have an expanded drill that will challenge the most seasoned firefighter.
So, for this example of drill progression we will use the “follow the coupling” drill. We start wtih one firefighter on a charged hose line. Black them out or in a smoked room, put them on the line somewhere in the middle. Have them find the coupling and make their way out. Easy enough.
Now, we want to build in the parameters for calling a Mayday, so we have them call the Mayday using LUNAR and they must communicate with command as they find their way out by “following the coupling.” Now they have to think about more than just following the coupling but the basic skill is still being used.
You get the idea. Here is how this drill can progress:
-One firefighter lost off of the line, one on the line. The one on the line verbally leads the lost firefighter to the line and they follow the coupling out.
-One firefighter has an air issue, they can buddy breath on the way out following the coupling.
-A downed firefighter on the line and his crew packages, fixes the air and removes him following the coupling out.
So, you can see that we can expand on this drill. Your only limited by your imagination and creativeness. Use caution not to make so unrealistic that it frustrates your firefighters though. It doesn’t take much to make a drill challenging; keep it simple.
Have a Blessed and Safe New Year and thanks for all of the support this year.
Jason
Buddy Breathing Hose Practice
Just a quick tip for practicing with your Buddy Breathing Hose. In our classes one of the skills that we notice to be week is the ability of firefighters to manage their Buddy Breathing Hose with gloves on. Although Buddy Breathing is not in the current SCBA standard, it is in the upcoming 2013 standard.
Obviously, drilling with your SCBA and using the Buddy Breathing Hose will increase your confidence and skill level. Getting out and using the SCBA and practicing during evolutions is always optimal. But, repetition can take place off of the drill ground.
To increase the amount of frequency that you get to connect and disconnect your Buddy Breathing Hose all you need to do is ride in your apparatus.
For most of us, not all, but the majority of us we have our SCBA in seat mounts so that when we mount the apparatus and buckle in we have the packs in our back. They are in the position they would be in if we were wearing them. This makes the ability to get to our straps fairly easy.
While riding around town, going to a non-urgent call, wear you gloves and find your Buddy Breathing Hose. As you ride, practice disconnecting it and connecting it over and over again. Try not to look while you do it. This will create muscle memory and confidence when we get on the drill ground.
Use your time wisely and be productive as often as you can. Be creative and you can practice other skills like knots while riding the apparatus.
Thanks for reading and train hard. As always, expect fire.
Company Drill: Standpipe Operations
This is a great drill from a great Brother and friend, Lance Peeples of the Webster Groves Fire Department in St. Louis County. Look for more great material from Lance in the future.
Daily Drill 1: Standpipe Operations
“The Daily Drill” is designed to spark discussion about operational issues in YOUR fire department. To do this we use photographs or videos depicting fire operations in other fire departments. We do not know the exact circumstances in which our Brothers in these fire departments are operating. Photos or videos are not intended to embarrass our BROTHERS and SISTERS but rather are intended to provide US with learning opportunities relevant to OUR specific operational framework. DON’TFOCUSONWHAT THEY’RE DOING…FOCUS ON WHAT YOU WOULD DO! Stay safe!
Watch the video below and answer the following questions:
1. Using the National Fire Academy Fire Flow Formula, what gpm would be required to extinguish a completely involved 500 square foot apartment fire?
How large of an undivided floor area is often found in high rise office buildings and what fire flow would be required there?
2. Under previous editions of NFPA 14 what was the minimum psi required to flow 500 gpm at the most remote riser?
3. What is the target gpm you are attempting to flow from your standpipe hose and nozzle combination? What psi must be available at the standpipe operation to supply that hose and nozzle combination in order to flow your desired attack flow?
4. The operation depicted showed using 4” supply line into the fire department connection. What is the working pressure limit of LDH used in your department? What is the elevation head pressure in a 30 story building? Are standpipe operations usually high flow or high pressure operations? Is using large diameter hose in FD standpipe connections a good idea?
5. What is the diameter of hose used in your standpipe pack? Is it an automatic/constant flow fog/smooth bore tip? What nozzle psi is required for its designed flow?
6. Will rust, scale, and other debris commonly found in standpipe systems pass through an automatic fog nozzle? Will rust, scale and other debris usually pass through an 1 1/8” smooth bore tip?
7. Can fire department pumpers ALWAYS be used to increase available pressure on the fire floor? What about damaged or missing FD connections? Pressure reducing and restricting valves? Missing piping or excessive head pressures?
8. At the One Merdian fire in Philladelphia on February 23, 1991 what was the length, diameter, and nozzle type (including psi/flow requirements) of the standpipe kits used by the fire department? Did this setup work? Why or why not?
9. What were the names of the Brothers that died at One Merdian that tragic day?
RIT Team Work
This video is the first team during a RIT evolution at Western Taney County Fire Protection District. They encountered wires and a wall with rebar in it. They had to call for resources and then they entered the room with trapped firefighters. They had to determine and try to fix the following:
Find the Firefighter
Fix any Air Problem
Disentangle/Disentrap
Package
Remove
This was the first team, more videos to come.
The Glove Friendly Face Piece
This photo shows a way to make an SCBA face piece for your RIT bag/kit glove friendly. You can use a garden hose or any kind of rubber tubing or hose that would be easy to grab with a gloved hand. We used a small bungee cord and ran it through the bonnet and attached both ends to the hose. This allows for easy feeling and grabbing the back of the mask with gloved hands.
We also attached large key rings to the pull tabs for the face piece bonnet to pull it tight. These rings can be any size you want, but make sure they are easily accessed and grabbed with glove hands.
These two methods have worked very well for us and during training evolutions has stood up to the pulling and tugging.
Let us know if you have other methods that work well for your department.
Thanks and keep training hard.
Jason
Thru the Floor Drill and Prop
Here is a short video of our thru the floor prop. This is soley for the use of calling a Mayday and recognizing that parameter. We place mattresses and foam below the firefighter and is monitored closely by our instructors.
This gives the firefighter a sensation of falling but is a short enough and controlled fall as to keep the drill safe. Email us if you would like to know how we built it.
Don’t Forget the Obvious: Basement Self-Rescue
In our classes we spend a lot of time showing firefighters how to stay out of and how to get out of bad situations. Our fire service is seeing an increase in firefighters who are falling through floors into basements or sub-levels. This is large part due to the engineered flooring systems that do not perform well in fire conditions.
Fires are growing more intense much faster than in the past and the structural members of these buildings are under attack before we arrive in some cases. The importance of knowing our response areas, getting an accurate size-up, doing a 360 evaluation of the building and choosing an appropriate tactic are more critical than ever.
We teach different methods of removing ones self from a basement and removing a downed firefighter from basements. There are several techniques for removing a firefighter including using an attic ladder, using the hose, rope, or webbing to lift them out of the hole. We can also cut the floor away from the exterior making a window a door to remove someone. These are just a few examples.
For self rescue we teach using a hand tool as a step or as a recent post by Chris Huston discusses, using the drywall as a ladder to get yourself out. We also teach using webbing as a stepping device with the assistance of firefighters on the outside. All of these techniques are good and and should be practiced. However, we know that if we fall through a floor we may lose our tools and it is going to be very bad down there. Speed is of the essence.
When go over the teaching points of basement rescues, we always talk about things to do to avoid this from happening in the first place. Doing a good 360, sound the floors, descend stairs feet first, know your still area and building construction are good places to start. I also like to point out that the hazards we discuss in regards to basements, junk and clutter, can also be our friend.
If you find yourself in a situation in a basement or an area with a high window for egress, use the stuff in that space as steps. Pile it up under that window and climb out. Don’t forget to use the obvious. I have done training in acquired structures where we put firefighters in the basement and they are free to use whatever is available. You would be surprised how many limit their resources to only what is in their hands or pockets.
Train hard and sometimes thinking outside the box is as simple as looking around at the “stuff” that is right at your feet. Thanks for reading and expect fire!
Jason